Clutch relearn - GT-R Register - Official Nissan Skyline and GTR Owners Club forum

MARKEER35 · 16th November 2011, 06:28 PM

Are these free when the car is serviced within warranty?? are these something that is necessary ???

What does it consist of??

Stevie76 · 16th November 2011, 06:42 PM

Yeah done during opt services. Hpc plugs consult 3 into car and kicks off relearn process. Takes a few minutes to complete. If you buy an AccessPort Nis006 you can do it yourself as and when you feel like it

Oh and yes it is required to avoid premature wear on the plates and ensure a smooth drive.

Kev@SVM · 16th November 2011, 08:39 PM

If you guys DIY lads be carefull

it is possible to do a bad Re learn

remember with Nis 06.. get to temp, set touch points and capacties to "zero" first, that's 0,0,0,0
Then Re- learn..Then re set touch and capacities on both baskets,
dont relearn unless you are on zero settings!!!

For tuned cars and cars with 14plate and 16 plate systems my advice is to set as low as poss ! you have a scale from -7 to +7
oem are normally set bang in the middle, Raising Figures, will put more load on clutches/gearbox kk

sumo69 · 16th November 2011, 10:22 PM

I have asked my local HPC to perform this as a stand alone piece of work as my car goes to Litchfield.

My car is 2 weeks beyond the annual anniversary and was told that Nissan won't allow dealers to do the work if its "late".

Is this more HPC verbal garbage?

D

enshiu · 16th November 2011, 10:25 PM

Quote:

Originally Posted by sumo69

I have asked my local HPC to perform this as a stand alone piece of work as my car goes to Litchfield.

My car is 2 weeks beyond the annual anniversary and was told that Nissan won't allow dealers to do the work if its "late".

Is this more HPC verbal garbage?

D

bs of course. like the tyres that can't be re-used.

if they don't do something email NMGB again.

Arcam · 16th November 2011, 10:27 PM

Quote:

Originally Posted by sumo69

I have asked my local HPC to perform this as a stand alone piece of work as my car goes to Litchfield.

My car is 2 weeks beyond the annual anniversary and was told that Nissan won't allow dealers to do the work if its "late".

Is this more HPC verbal garbage?

D

Must admit it sounds iffy to me David, perhaps try another NHPC and see what they say, but I can see a case if you were away on holiday and booked the POS 2 weeks late

Stevie76 · 16th November 2011, 10:28 PM

Total bollocks again. Iain and the team will be doing this as part of your services....no need to go to the stealers....

enshiu · 16th November 2011, 10:31 PM

Quote:

Originally Posted by Stevie76

Total bollocks again. Iain and the team will be doing this as part of your services....no need to go to the stealers....

+1,000

Arcam · 16th November 2011, 10:39 PM

Quote:

Originally Posted by Stevie76

Total bollocks again. Iain and the team will be doing this as part of your services....no need to go to the stealers....

He would get the relearn and cylinder balance as part of Ian's service but would have to pay extra for the alignment that would be included with a POS from an NHPC.

Stevie76 · 16th November 2011, 10:46 PM

All built in and still half the price of the hpc's....mine has not long had it's 12 month service (sept) and laser alignment done as matter of course.

http://www.litchfieldimports.co.uk/G..._and_costs.pdf

Arcam · 17th November 2011, 08:20 AM

Quote:

Originally Posted by Stevie76

All built in and still half the price of the hpc's....mine has not long had it's 12 month service (sept) and laser alignment done as matter of course.

http://www.litchfieldimports.co.uk/G..._and_costs.pdf

Fair comment Stevie, should have read the menu better

bobel · 17th November 2011, 08:33 AM

Its crap like that from HPC's that has lads running a mile to the independents, personally I don't see a need to engage with the HPC's unless your looking for warranty work or have no independent within a reasonable distance, it is also clear from numerous threads that the independents are far more knowledgable particularly with regards tp the GR6 transmission, I very much doubt any of the HPC's have ever even worked on a GR6 beyond the routine maintenance, they just tend to replace the whole thing!!! bonkers

enshiu · 19th November 2011, 07:41 PM

so standard clutch plates 0,0,0,0 right?

why do I have to wait till 55C?

lawsy · 19th November 2011, 07:53 PM

Quote:

Originally Posted by enshiu

so standard clutch plates 0,0,0,0 right?

why do I have to wait till 55C?

Because the plates will no doubt behave different at different temps.

Chris956 · 20th November 2011, 10:05 AM

David - the over run time for the service schedule is 1 month ( and even that is negotiable depending on which HPC you speak too ) which allows for holidays etc etc not 2 weeks - thats ridiculous

16th November 2011, 06:28 PM	#1 (permalink)
MARKEER35 MARKEER35 is unaware they can edit their status GTR Register User Join Date: Jul 2011 Location: DORSET Posts: 115	Clutch relearn Are these free when the car is serviced within warranty?? are these something that is necessary ??? What does it consist of?? __________________

16th November 2011, 06:42 PM	#2 (permalink)
Stevie76 Stevie76 is unaware they can edit their status GTROC Member Join Date: Dec 2009 Cars owned: Current: 650R DMG R35, Clio Sport 200, 1992 205 Mi16, Audi A4 2.0tdi Posts: 2,747	Yeah done during opt services. Hpc plugs consult 3 into car and kicks off relearn process. Takes a few minutes to complete. If you buy an AccessPort Nis006 you can do it yourself as and when you feel like it Oh and yes it is required to avoid premature wear on the plates and ensure a smooth drive. __________________ 2010 DMG Premium R35 - SVM 650R (Terminator) - ID1000 Injectors, GTC Wrapped Downpipes, Whifbitz 102mm Exhaust, SVM / GTC Intakes (K&N Filters), SVM Bumper Intakes, SVM Bov's, SVM / GTC Intercooler Pipe Kit, SRD Intercooler, GTC Rear Light Kit, VM Gloss Black Wheels, NIS006 & GTC Custom tune, AP Discs, Carbotech Pads, Eibach ARB's, Dodson Circlips, Gotboost Extinguisher Mount, Rexspeed Carbon Exhaust tips, Mines Steering Wheel, Endless Bonnet Ram Mod Last edited by Stevie76; 16th November 2011 at 06:44 PM..

16th November 2011, 08:39 PM	#3 (permalink)
Kev@SVM Kev@SVM is @ www.severnvalleymotorsport.co.uk NEWWEB SITE R35 GT-R Specialists Join Date: Nov 2010 Location: Telford, Shropshire Posts: 3,280	If you guys DIY lads be carefull it is possible to do a bad Re learn remember with Nis 06.. get to temp, set touch points and capacties to "zero" first, that's 0,0,0,0 Then Re- learn..Then re set touch and capacities on both baskets, dont relearn unless you are on zero settings!!! For tuned cars and cars with 14plate and 16 plate systems my advice is to set as low as poss ! you have a scale from -7 to +7 oem are normally set bang in the middle, Raising Figures, will put more load on clutches/gearbox kk __________________ Kevan Kemp: SVM - World Record Holder's in 2012 - Tel : +44(0)1952 583 917 - Web: To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. R35 Servicing & Repairs Consult 3, Cobb & Syvecs Conv - From 570R to 1800R UK & Euro Record Holders 2010,2011 & 2012 8.93 @ 168.56mph @ Santa Pod - Oct 2012 World's Fastest R35 GT-R @ 218mph - March 2012 World's Fastest standing 1KM 208.2mph - July 2012

16th November 2011, 10:22 PM	#4 (permalink)
sumo69 sumo69 is now Stage 4 and MY12 software GTROC Member Join Date: Mar 2008 Posts: 2,144	I have asked my local HPC to perform this as a stand alone piece of work as my car goes to Litchfield. My car is 2 weeks beyond the annual anniversary and was told that Nissan won't allow dealers to do the work if its "late". Is this more HPC verbal garbage? D __________________

16th November 2011, 10:28 PM	#7 (permalink)
Stevie76 Stevie76 is unaware they can edit their status GTROC Member Join Date: Dec 2009 Cars owned: Current: 650R DMG R35, Clio Sport 200, 1992 205 Mi16, Audi A4 2.0tdi Posts: 2,747	Total bollocks again. Iain and the team will be doing this as part of your services....no need to go to the stealers.... __________________ 2010 DMG Premium R35 - SVM 650R (Terminator) - ID1000 Injectors, GTC Wrapped Downpipes, Whifbitz 102mm Exhaust, SVM / GTC Intakes (K&N Filters), SVM Bumper Intakes, SVM Bov's, SVM / GTC Intercooler Pipe Kit, SRD Intercooler, GTC Rear Light Kit, VM Gloss Black Wheels, NIS006 & GTC Custom tune, AP Discs, Carbotech Pads, Eibach ARB's, Dodson Circlips, Gotboost Extinguisher Mount, Rexspeed Carbon Exhaust tips, Mines Steering Wheel, Endless Bonnet Ram Mod

16th November 2011, 10:46 PM	#10 (permalink)
Stevie76 Stevie76 is unaware they can edit their status GTROC Member Join Date: Dec 2009 Cars owned: Current: 650R DMG R35, Clio Sport 200, 1992 205 Mi16, Audi A4 2.0tdi Posts: 2,747	All built in and still half the price of the hpc's....mine has not long had it's 12 month service (sept) and laser alignment done as matter of course. http://www.litchfieldimports.co.uk/G..._and_costs.pdf __________________ 2010 DMG Premium R35 - SVM 650R (Terminator) - ID1000 Injectors, GTC Wrapped Downpipes, Whifbitz 102mm Exhaust, SVM / GTC Intakes (K&N Filters), SVM Bumper Intakes, SVM Bov's, SVM / GTC Intercooler Pipe Kit, SRD Intercooler, GTC Rear Light Kit, VM Gloss Black Wheels, NIS006 & GTC Custom tune, AP Discs, Carbotech Pads, Eibach ARB's, Dodson Circlips, Gotboost Extinguisher Mount, Rexspeed Carbon Exhaust tips, Mines Steering Wheel, Endless Bonnet Ram Mod

17th November 2011, 08:33 AM	#12 (permalink)
bobel bobel is Saving hard for his next mod GTR Register User Join Date: Jul 2010 Cars owned: R35, E92 335d Posts: 902	Its crap like that from HPC's that has lads running a mile to the independents, personally I don't see a need to engage with the HPC's unless your looking for warranty work or have no independent within a reasonable distance, it is also clear from numerous threads that the independents are far more knowledgable particularly with regards tp the GR6 transmission, I very much doubt any of the HPC's have ever even worked on a GR6 beyond the routine maintenance, they just tend to replace the whole thing!!! bonkers __________________

19th November 2011, 07:41 PM	#13 (permalink)
enshiu enshiu is away Executive GTR Owners Club Member Join Date: Aug 2010 Location: Japan,UK,NL Cars owned: 2008 R35 GT-R JDM Black Premium Edition COBB stage 2 (+/-560bhp),JDM Toyota Camry,(winter use) Subaru Vivio Posts: 2,755	so standard clutch plates 0,0,0,0 right? why do I have to wait till 55C? __________________ Now: R35 GTR JDM - JDM Gen 3.5 Camry - EDM Subaru vivio Past: R33 GTR sgl turbo

20th November 2011, 10:05 AM	#15 (permalink)
Chris956 Chris956 is 420bhp RWD is interesting in the rain :-0 GTR Register User Join Date: Apr 2010 Cars owned: From GTR To GT3 Posts: 1,663	David - the over run time for the service schedule is 1 month ( and even that is negotiable depending on which HPC you speak too ) which allows for holidays etc etc not 2 weeks - thats ridiculous __________________

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread: