Taff*tune GTS R32 *56k huge no no* - Page 7 - GT-R Register - Official Nissan Skyline and GTR Owners Club forum

Butuz · 13th November 2006, 04:27 PM

Mmmmm r34 headlights

Yummmmmmy

Butuz

Cord · 15th November 2006, 09:17 AM

Why have you gone bottom pivoted clutch and brake, but top pivoted throttle? Do you not think it will hinder heel and toeing, and feel strange when swapping from throttle to brake?

sideways.taff · 15th November 2006, 12:08 PM

I'm going to try a top pivoted throttle first, if that doesn't work too well then I'll make a floor mounted one.

[j]Desing · 15th November 2006, 06:57 PM

Awesome, looks like the project is comming along.

Faz Choudhury · 16th November 2006, 08:49 AM

Can't believe I have missed this...AMAZING project and hats off to you for undertaking such a job. You are obviously very gifted when it comes to this. Looks the boll$$cks so far

sideways.taff · 18th November 2006, 06:27 PM

My new intercooler turned up yesterday which is a bit smaller than the one that I had in there for mockup and a hell of a lot lighter and perfect for my application without needing to modify it at all.

Today I set about making a mount for it and the bumper combined and I must say I'm pretty chuffed with todays efforts even though the welder was being a complete ****** and I had to strip it down to clean the insides out at one point!

I reckon the bonnet needs a big trim job to get it to fit lol!

I'm going to put some vertical stays in to support the front of the bracket and probably brace it to the bottom of the radiator support. As it is now, left unsupported the front sags about 5mm so I need something to brace it back up, but that will have to wait until I have a new section between the chassis rails (damn rust!)

junglechink · 21st November 2006, 02:39 PM

nigel f · 21st November 2006, 03:27 PM

Cars coming on well, I am very impresed with the effort and the results,

I also see from the Photos that the Plugs and Grout in the Kitchin isnt finished.

Proitrys are in favour of the car

Well done

Nigel

sideways.taff · 21st November 2006, 06:09 PM

hahaha, that tile work is my dads forte lol. I have nothing to do with DIY around here, it aint my house lol!

Snowfiend · 21st November 2006, 06:11 PM

Quote:

also see from the Photos that the Plugs and Grout in the Kitchin isnt finished.

LOL Nigel

Come on Sideways.Taff......stop going to work all day and get this project finished

Big Drifter · 22nd November 2006, 06:20 PM

Wat are you doing with the old engine, gbox and the bodykit u used at the start?

sideways.taff · 22nd November 2006, 09:57 PM

All gone! The RB20DE and gearbox I gave away free to a good home and the bodykit was sold to Alex j B on here.

Conrad · 23rd November 2006, 01:36 PM

Quality Taff, coming on nicely

°GREGZILLA° · 23rd November 2006, 03:02 PM

it's simply amazing

very good work mate

DRAGandDRIFT · 23rd November 2006, 05:05 PM

speechless.......such an informative project......makes me want to get some plasticine and make something.

13th November 2006, 04:27 PM	#91 (permalink)
Butuz Butuz has no status. GTR Register Member Join Date: Jan 2005 Location: Cardiff, UK Cars owned: R32-GTSTaffTune Posts: 496	Mmmmm r34 headlights Yummmmmmy Butuz __________________

15th November 2006, 09:17 AM	#92 (permalink)
Cord Cord has no status. GTR Register Member Join Date: Aug 2002 Location: RB Motorsport Cars owned: dirty poo Posts: 1,568	Why have you gone bottom pivoted clutch and brake, but top pivoted throttle? Do you not think it will hinder heel and toeing, and feel strange when swapping from throttle to brake? __________________

15th November 2006, 12:08 PM	#93 (permalink)
sideways.taff sideways.taff has no status. GTR Register Member Join Date: Mar 2005 Location: Carmarthenshire, Wales Cars owned: R32 GT-R Posts: 480	I'm going to try a top pivoted throttle first, if that doesn't work too well then I'll make a floor mounted one. __________________

15th November 2006, 06:57 PM	#94 (permalink)
[j]Desing [j]Desing has no status. GTR Register Member Join Date: Oct 2006 Location: Phoenix, AZ Cars owned: Celica,WRX Posts: 175	Awesome, looks like the project is comming along. __________________

16th November 2006, 08:49 AM	#95 (permalink)
Faz Choudhury Faz Choudhury is wondering what this status things all about? GTR Register Member Join Date: Apr 2005 Location: London Cars owned: 2004 M3 Convertible Posts: 1,952	Can't believe I have missed this...AMAZING project and hats off to you for undertaking such a job. You are obviously very gifted when it comes to this. Looks the boll$$cks so far __________________

18th November 2006, 06:27 PM	#96 (permalink)
sideways.taff sideways.taff has no status. GTR Register Member Join Date: Mar 2005 Location: Carmarthenshire, Wales Cars owned: R32 GT-R Posts: 480	My new intercooler turned up yesterday which is a bit smaller than the one that I had in there for mockup and a hell of a lot lighter and perfect for my application without needing to modify it at all. Today I set about making a mount for it and the bumper combined and I must say I'm pretty chuffed with todays efforts even though the welder was being a complete ****** and I had to strip it down to clean the insides out at one point! I reckon the bonnet needs a big trim job to get it to fit lol! I'm going to put some vertical stays in to support the front of the bracket and probably brace it to the bottom of the radiator support. As it is now, left unsupported the front sags about 5mm so I need something to brace it back up, but that will have to wait until I have a new section between the chassis rails (damn rust!) __________________

21st November 2006, 02:39 PM	#97 (permalink)
junglechink junglechink has no status. GTR Register Member Join Date: Jul 2005 Location: Naples, Italy Cars owned: 1992 R32 Posts: 47	Dreams DO come true. __________________

21st November 2006, 03:27 PM	#98 (permalink)
nigel f nigel f has no status. New Users Join Date: Sep 2002 Location: East yorkshire Cars owned: R33 GTR V SPEC, R34 GTR Posts: 1,653	Cars coming on well, I am very impresed with the effort and the results, I also see from the Photos that the Plugs and Grout in the Kitchin isnt finished. Proitrys are in favour of the car Well done Nigel __________________

21st November 2006, 06:09 PM	#99 (permalink)
sideways.taff sideways.taff has no status. GTR Register Member Join Date: Mar 2005 Location: Carmarthenshire, Wales Cars owned: R32 GT-R Posts: 480	hahaha, that tile work is my dads forte lol. I have nothing to do with DIY around here, it aint my house lol! __________________

22nd November 2006, 06:20 PM	#101 (permalink)
Big Drifter Big Drifter has no status. GTR Register Member Join Date: Nov 2006 Posts: 7	Wat are you doing with the old engine, gbox and the bodykit u used at the start? __________________

22nd November 2006, 09:57 PM	#102 (permalink)
sideways.taff sideways.taff has no status. GTR Register Member Join Date: Mar 2005 Location: Carmarthenshire, Wales Cars owned: R32 GT-R Posts: 480	All gone! The RB20DE and gearbox I gave away free to a good home and the bodykit was sold to Alex j B on here. __________________

23rd November 2006, 01:36 PM	#103 (permalink)
Conrad Conrad has no status. GTR Register Member Join Date: Jul 2004 Location: RIP TweenieRob ! Cars owned: AE86, R33GTR, EVO IXGT Posts: 365	Quality Taff, coming on nicely __________________

23rd November 2006, 03:02 PM	#104 (permalink)
°GREGZILLA° °GREGZILLA° has no status. GTR Register Member Join Date: Aug 2004 Location: @ Kamikaze-Garage in belgium Cars owned: BNR32 single turbo,bnr 32 stock and a cefiro for drifting. Posts: 147	it's simply amazing very good work mate __________________

23rd November 2006, 05:05 PM	#105 (permalink)
DRAGandDRIFT DRAGandDRIFT has no status. GTR Register Member Join Date: Sep 2006 Location: Endless desu Cars owned: R32,R33,R34 Posts: 750	speechless.......such an informative project......makes me want to get some plasticine and make something. __________________

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread: