R34 MFD not working

[hyrev]

I really wonder, before I make the trip, that if SuperAutobacs can do it. If not, would
they then ship it to a 3rd party? All was fine until it just went out. I wish I knew of a
shop that specializes in this or a person. Really frustrating. Oh well, I will bring it with me
tonight and perhaps a Immortal GTROC member will be there or someone that has dealt
with this before.

Aki, you are right, it could be an easy fix or it could be something more severe. Better
have the entire thing checked out to avoid any other aggrevation and or frustration.

PS. OT though, could not get any

[akasakaR33]

Paul - thanks for trying (for the raisinents - my wife's favorite). As for SuperAutobacs, I meant for the fuse holder, not for those goons to tamper with your car...

see you guys soon.

[sweepy125]

i could fix it for you iv soldered tiny bits back to mobile phones in the past if you could supply the fuse and send me the board i would be happy to do it for you

[hyrev]

ARGHHHH - WTF!

Ok, feel a little bit better. Ok. had the fuse replaced and put everything back together
and then plugged it all up. Turned on the ignition and it came one! Yes! Then, yes, there
is a then..... it began to fade again. It first dimmed and then went black again. So, good
news is that the screen works, right. Bad news is that there is something causing this.

So anyone here in Japan know where to get this fixed? Perhaps Sharp or Nissan could
point me in the right direction? At this point I am pretty frustrated, although it is too
early to go out and get a whole new unit. Can anyone here ask any of their local HPC
or dealers/tuners of somewhere I can either go to or ship it to? Thank you in advance.

When I did turn it on, the NISMO screen popped up along with the gauges then fade to
black shortly after, about 7 seconds or so. I would think being in Japan there would be at
list 1 million electricians that could fix this (I am stereotyping here - sorry about that) but
I need to be pointed in the right direction rather than drive to every single shop and get
turned down or get the "sucking air through teeth" response followed by a big fat NO.

[Rain]

did it blow the fuse again? have you checked?

[hyrev]

Originally Posted by Rain

did it blow the fuse again? have you checked?

Yes, it blew. I pulled it out this am and had a look. But, I also saw this:



Since I have the Sharp screen, I use the 30 pin connection in red. But the
Toshiba uses a 30 and 6 pin connection, perhaps for the yellow one? Please
let me know if this is correct and if anyone has done this. If so, then I can
go ahead and purchase the Toshiba screen as those are always on the Yahoo
auctions in Japan for about $300 or so. Then I would need to get the 6 pin
connector somewhere - d'oh! The Sharp model # is 6L-U7WJ and or LQ6B50N.

Also, if it is the power inverter that is causing my issues, where would that
be located, out of curiousity? Would it be on the lcd portion or on the circuit
board itself? (NISMO V2 board). The screen lit up momentarily when the fuse
was replaced and then went back to black.

[akasakaR33]

Paul - here you go - Yahoo!¥ª¡¼¥¯¥·¥ç¥ó - ¡ú¡ù¥·¥ã¡¼¥×À½±Õ¾½¥æ¥Ë¥Ã¥È¡ú£¶L-£Õ£·£×£Ê¡úÃæ¸ÅÉÊ¡ù¡ú

Although it says it's not been tested, no cracks. Protective film is still on it.

Aki