GTR Forum banner
1 - 20 of 26 Posts

·
Registered
Joined
·
234 Posts
Discussion Starter · #1 ·
So after sevral months of building and waiting and waiting ..... and waiting I finally got my project going in a direction. It.s not done but it's on its way, here are a few shots of the car in it's current state.



Engine:
Greddy TD05-16G's
Greddy tubular exhaust manifold
Greddy 51mm waste gate
Greddy fuel rail
Greddy Oil filter re-location
Grex Oil cooler
Greddy timing belt
Greddy metal intake gaskets
RIPP Power Steering reservoir
RIPP Boost cooler (methanol/water injection system)
4" radiator
FAL Coolant fan
N1 Nismo water pump
Amsoil coolant
Tial Blow Off Valve
ARC Front mount
Apexi N1 exhaust
Tomei PONCAM's
Tomei cam gears



Supension:
Grex Coil over suspension
Gullflame 18X10 wheels
BF Goodrich 255-40-18 tires



Transmissnion:
Exceedy triple plate clutch
Nismo clutch master cylinder
Nismo short shift kit
Castrol hydraulic fluids
Carbon Fiber 1 PIECE Drive shaft



Fuel:
RC 750cc injectors
Aeroquip fuel filter
Walboro fuel pump
-6 Fuel Feed line
-4 return line
Aeromotive Fuel pressure regulator
Aeroquip Fuel pressure lines
Earls fittings



Exterior:
Carbon Kevlar hood
PIAA Lights



Interior:
MOMO Corsa Pedals
Sparco Leather Turino Seats (Matching Baby seat)
TYPE S weighted shift knob




Electonics
Greddy ProFec B Spec 2 Boost controller
Dual PLX Wideband O2’s
Autometer 40psi Boost gauge
Apexi AFC2
Silver face back light gauges

Many thanks to:
GTR Forums UK
DAVE
Hyrev

I'm hooked... I get it now..... I like this GTR thing

Ross
 

·
Registered
Joined
·
229 Posts
Looking good Ross. Good luck. I'll stop by with mine one day.

John
 

·
Registered
Joined
·
234 Posts
Discussion Starter · #9 ·
jas3113 said:
Looking good Ross. Good luck. I'll stop by with mine one day.

John
Totally Looking forward to cruising with you….

skylife said:
wow, nice cf driveshaft. not very common mod, atleast not around my ways. good job there, looks good.
Yes….. your right a very uncommon mod… totally worth the weight (LOL) the full 1pc shaft weights 16lbs….total its beautiful, shames you don’t see it.

EvolutionVI said:
Looks really good,like it.

But: do you like the steering wheel and the gauges:rolleyes:

Alex
Well, keep in mind, we are in the states and what’s “IN” here may not be in where you are… The gauges are Twin Wide bands at a value of about $1000 us, the Sparco wheel in brand new a 2006 model, and the white face gauges are in Miles Per Hour and freshen up the look…. So in short yes, thank you I do like the set up….

hyrev said:
nice choice on the hood - def. different
it is going to be a BEAST
Thanks man.... and thanks again for the help....

DaveW was right the Twin 16’s rock, the response is awesome.... I can't wait to strap it down and tune it up....

Still to come:
  • Power FC De-Jerto
  • Greddy Profec B series 2
  • RIPP Boost Cooler
  • Carbon lip
  • Carbon interior
  • Carbon
  • Wing center
  • Rear defuser
  • Front defuser
  • Nismo LSD
  • Attessa Controler
 

·
Vendor
Joined
·
12,722 Posts
looks good, nice close ratio gearbox is needed to take advantage of those mod's.:bowdown1: :bowdown1:
 

·
Registered
Joined
·
234 Posts
Discussion Starter · #14 ·
davew said:
looks good, nice close ratio gearbox is needed to take advantage of those mod's.:bowdown1: :bowdown1:
Yes... Yes... do you have an opinion on a set, I have a spare trans I could build out of the car:squintdan ?


rico2k_uk said:
thats looking good! needs to be a little lower ;)

take off that steering wheel tho - a little chav!

Thank you

Yes, I agree however since I just put it in I was hoping it would settle a bit and then I'll re-adjust...
 

·
Registered
Joined
·
646 Posts
Ross,

Awesome 33 man,
What numbers are you hoping for?
What Engine Management are you going to use?

I really like the propshaft, that is a lovely piece of kit.
Who makes it and how much..

Same goes with the 4" Radiator too?!
 

·
Registered
Joined
·
234 Posts
Discussion Starter · #19 ·
LAURENCE said:
Ross,

Awesome 33 man,
What numbers are you hoping for?
What Engine Management are you going to use?

I really like the propshaft, that is a lovely piece of kit.
Who makes it and how much..

Same goes with the 4" Radiator too?!
Thanks....

I was looking for a solid 400-500 and today it made 470ish.... I'm using a Power FC, but today I tuned with just and AFC-2....

The propshaft is Greddy Trust Item and is about $3650(US)....

The radiator is custom.... from cool-tech in the US....
 

·
Registered user
Joined
·
6,821 Posts
. . nice project

You are going to add some carbone parts, did you already sorted out wich parts to use? Are going for normal Carbone interior parts, I heard in the US there are now carbone-kevelar parts availble for some cars. Looks great.

If you are looking for diffusers in carbone , I recomande garage Defend Japan custome diffusers (for R34 and R33).







:cool:
 
1 - 20 of 26 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top